Jan 14

Scrap of the week #9

I keep forgetting to post a Scrap of the Week. I usually do this on a Monday, but as the weather is just as miserable as Monday’s was (grey and drizzly) I’m sure nobody will notice the difference. Ladies and gentlemen, I’m delighted to present… [cue drumroll] my first scrap of 2011!

C&A sweater label

C&A felted sweater

This is from the bag of felted sweaters given to me by the very generous Becky Button.

Its particulars:-

Item: gent’s v-neck long-sleeved sweater

Fibre: 100% lambswool

Colour: marled grey

Make: C&A [By the way, this label looks like the old C&A to me, but I'm no expert. Anyone have any insight?]

Size: originally large, but now substantially smaller

You can see the slippers I made with this in my last post. I used this sweater because it was about the thickness of felt recommended in the Martha Stewart pattern: 1/8 of an inch. That pattern is one that’s freely available on her site. Given that it’s offered free, it would be unreasonable to expect a huge amount of detail or hand-holding. I’ve made some observations on how best to approach this pattern later on.

Working with felted garments. It can be tricky, when working with reclaimed garments, to assess whether you have enough material to meet your pattern’s requirements. This started out as a large gent’s sweater, and I was surprised that it took most of the front and back to make these size 8 slippers. The arms and some useful scraps – including the ribbed edging – are left to use on other projects. Something else to bear in mind is that some felted garments have a radically different appearance on the right and wrong sides, so it’s wise to be consistent in using one side or the other. In this case, I decided that there was a nicer texture to the inside.

Sweater to slipper

Deconstructing the old garment

My notes on the pattern:-

Enlarging. First you have to enlarge the little templates of the two pattern pieces to the required shoe size. Helpful enlargement guidelines are given on the pattern. Bear in mind that it’s in US sizes. Another word of caution: don’t take the enlargements listed as gospel; I found that they came up very small. It could be that my photocopier isn’t as good at maths as Martha’s is. Fortunately, I had a proxy for the slipper recipient at home (with same shoe size) so was able to test it before committing to cutting out. I had to enlarge by 400% in the end to achieve a size 8; that’s the biggest enlargement my photocopier extends to, by the way. But I’d recommend drawing around the slipper-wearer’s feet, just to double-check for errors. Remember to factor in a small seam allowance of 3/16 of an inch all round the sole.

Cutting out the side

Cutting out an instep

Pattern adjustments. In terms of the shapes of the pattern pieces, I thought they could do with some light revising. I liked the shape of the sole, but the instep curve (that seam on the top of the foot) could be just a little more shapely and have a more graceful sweep. I’d also like to try lowering the cut of the entire instep to make the slippers easier to get into, allow a snugger fit, and maybe a prettier shape for a female foot. But I’m not really complaining. Martha offers another slipper pattern, made from a single upper, which seems to check the boxes on the prettier girl shape.

On to the sole, the instructions advise using two layers of felt for the sole, and that worked fine. You could try using a single layer of really thick felted garment instead. Or maybe put some padding between the two felt layers of sole; Vintage Violet had a very precise product suggestion to that effect in the comments of my last post (Thanks, VV!).¬† I’d also like to try making it with other materials: a suede or leather sole, perhaps, as this slipper is really a house-with- immaculate-carpets slipper, not a cold-stone-floors slipper (which is really what I need).

Cutting out. There’s something very pleasing about cutting out felt with a nice sharp pair of scissors. I’d liken it to walking on fresh snow. Do keep your wits about you as you cut, though. If you have felt with a pronounced right side, pinning little paper labels to that side of the fabric leaves nothing to chance. Otherwise, it’s so easy to get confused.

Compiling pieces

Most of a slipper, ready to go

Bear in mind that you need two right side insteps, two left side insteps (one for each slipper). You also need 4 soles (and possibly an inner sole for added padding, though two nice thick layers of felt weren’t bad). Do check and check again during construction that you are doing a pair, not two identical shoes. It’s an easy mistake to make; halfway through tacking on the 2nd sole I realised I’d done two left feet… Nyarg!

Attaching the sole

Pinning on the sole

Making up. Remember that the seams are on the outside; I know it sounds obvious, but some of us start sewing on auto and then get into trouble. The two top pieces go together easily; you can just pin them together at the back and instep and sew them straight off on your machine, leaving the recommended 3/16th of an inch seam allowance. Despite what you may have been told, you can usually sew right over pins on your machine, though you must have the pins lying perpendicular to your seam, and try to have the tips of the pins poking through the upper side of the fabric so that they don’t scratch your machine bed. When I stitched these, I removed each pin as my presser foot approached it as my machine just wouldn’t have made it over all that thick felt plus a pin too. The soles, though, were a little more fiddly and required careful easing, pinning (beginning at the centre of the heel) and tacking (at which point pins could be removed) to prevent the pieces sliding apart during sewing. I set my machine for a fairly big stitch (approximately 9 stitches per inch), and used vintage Sylko Dark Elephant thread on Josephine (a vintage Singer 99k). The use of vintage materials and tools is not obligatory, but I would obviously contend that it enhances the sewing experience. [winks]

Pinning the sole

Eased and pinned

Embellishments. I left these slippers plain. The instructions recommend embroidering a big “X” on each slipper, but the embroidery opportunities are endless. I’d like to try constructing the sole seams with hand-stitched blanket stitch instead of machine stitching, for a different effect. A pattern of punched holes around the top edge would also be a fun. You could add a label to the inner sole before construction (machine- or hand-sewing it in), or a loop of ribbon to the back of the heel at the end. Oh, the possibilities!

Sole close-up

Finished slipper sole

These were very quick and satisfying to work, even with all the fiddly pinning and tacking, so I hope you’ll give them a go. Just to remind you that there are more pictures of the finished slippers – which were a gift to my brother – over here. I can’t wait to make more. Little Scraplet has already ordered an orange pair, which should be quick and easy¬† to do as he has such little feet. Off to rootle through my stash…

Share This
Related Posts Plugin for WordPress, Blogger...

2
comments

2 comments!!!

  1. Fiona Davies says:

    What a fab post, who knew you’d be able to make such lovely slipper from an old sweater. Thanks for posting this :)

  2. Zoe says:

    These look great! My mum made great felt slippers one year by using leather inner-soles as the sole (ie, normally the leather goes inside your shoe, she used it leather side down under the sole) for a more durable, cold-floor slipper. Worked a treat, and you can use a pair bigger than your slippers and cut them down to shape to fit your pattern. Easy peasy!

Reply

Socialized through Gregarious 42